Johnson City Drywall | Drywall Installation in Johnson City, TN

Johnson City Drywall hangs and finishes gypsum board for new construction, room additions, garages, basements and ceilings across Johnson City and the Tri-Cities. Every job runs the same order: sheet layout and cutting, fastening to studs or joists, corner bead, then three coats of joint compound over every seam and screw head, then sanding to whatever finish level your paint needs. Whole houses, single rooms, and everything in between, on new builds and remodels alike.

Get a Quote Call (423) 820-3689

We work in single-family homes, multi-room remodels and custom builds, and we carry the sheetrock the room calls for: standard 1/2 inch gypsum panel on most walls, moisture-resistant board where a bathroom or a basement needs it, and 5/8 inch Type X where fire separation code applies. Many years of hanging and finishing goes into knowing which board belongs where, and into making the seam between new drywall and existing wall disappear under paint. Same crew and the same pricing from Johnson City out through Kingsport, Bristol, Elizabethton, Jonesborough, Gray, Erwin, Piney Flats and Boones Creek.

Drywall Installation Services

New Construction Drywall

Full drywall hanging, taping, and finishing for new-build rooms and additions. For a ground-up new build or a whole-home job, see our dedicated New Construction & Whole Home Drywall page. For just the hanging step, see Drywall Hanging.

Room Additions & Renovations

Tying new drywall into existing walls and ceilings without a visible seam line.

Kitchen & Bathroom Remodel Drywall

Remodels usually mean cutting drywall around new plumbing, electrical, and cabinet layouts rather than a clean open wall, moisture-resistant board is standard in these rooms, and precise cuts around fixtures matter more here than in a straightforward new-build wall.

Garage & Basement Drywall

Garages need fire-rated board where they share a wall with living space, see our Garage Drywall page for the specifics. Basements need moisture-resistant board, see Basement Drywall.

Ceiling Drywall Installation

Ceiling work carries more weight and requires different fastening than wall work. Full details on our Ceiling Drywall Installation page.

Why Choose Johnson City Drywall for Drywall Installation?

Many Years of Experience: a team that has done this work long enough to get it right the first time.
Walls That Actually Look Finished: the right board for the room, staggered seams, and a finish level matched to your paint, so the wall looks right under normal light, not just from across the room.
A Job That Stays on Schedule: we give you a real timeline up front instead of a vague “we’ll get to it,” and we stick to it.
We Know the Area: from Johnson City out through Kingsport, Bristol, and the surrounding towns, including what it means for licensing if your project is a bigger one.

Not sure what your wall actually needs?

Tell us what the damage looks like, or what needs hanging, and you get a real number and a real timeline before anything is cut.

Request a Quote

Materials We Work With

Standard 1/2” drywall: most interior walls
5/8” fire-rated (Type X) drywall: required where code calls for it, including garage/house separation walls
Moisture-resistant (green board): basements, bathrooms
Soundproof drywall: shared walls, home offices

Sheet Sizes

Drywall comes in a few standard sheet sizes, and the size we use affects how many seams a room ends up with. 4x8 sheets are the standard choice for most rooms, easier to carry and maneuver in tight spaces. 4x12 sheets cost a bit more to work with but leave fewer seams, which is why we often use them on ceilings and long walls where fewer joints means less finishing work and a cleaner final surface.

Finish Quality. Level 4 vs. Level 5

Most homes are finished to Level 4: two coats of joint compound over the flat joints, one coat over the corners, three coats over fastener heads, sanded smooth. That’s the standard finish under flat paint, light texture, or wallpaper.

Level 5 adds a full skim coat over the entire surface on top of the Level 4 work. It costs more and takes longer, but it’s worth it under glossy paint, dark or deep-tone paint, or in rooms with strong side-lighting (windows, recessed lighting), those conditions show every flaw a Level 4 finish would otherwise hide. We’ll tell you honestly which one your room actually needs rather than upselling a skim coat you don’t.

What a Good Installation Prevents

A drywall job done right the first time means fewer callbacks later. Fasteners spaced and seated correctly, rather than driven too shallow or too deep, are what keep nail pops from showing up as the house settles over the next few years. Properly staggered seams and fully embedded tape are what keep joints from cracking along the same line repeatedly. A lot of what we cover on our Drywall Repair page, nail pops, seam cracks, traces back to shortcuts taken during the original hang, not just normal wear.

Running a taping knife along a drywall seam

One crew, one quote

Hanging, taping, finishing, sanding and the texture match run as one job on one schedule, rather than a hanger who leaves and a finisher who never turns up.

Floors get covered, the work area gets closed off and sanding is done with vacuum-assisted tools, so the only room that knows we were there is the one with the repair in it.

See all services

How Much Does Drywall Installation Cost?

Installation typically runs $1.50 to $3.00 per square foot, installed. Labor makes up most of that, around $1.00 to $2.10 per square foot, with materials adding $0.55 to $0.90 per square foot depending on the type of board used.

For reference: a single room hung and finished typically lands between $1,200 and $2,500, depending on its size, its ceiling height and the board it needs. A small bedroom sits at the bottom of that range and a large living room with a vaulted ceiling at the top. Whole-house and multi-room work is quoted off the square footage rather than by the room. You get an exact number after we see the job, and the price you approve is the price you pay unless the scope itself changes.

How Long Does Installation Take?

Single room: 2 to 3 days
1,000 sq ft: 4 to 7 days
2,000 sq ft: 7 to 10 days
3,000 sq ft: 10 to 14 days

That breaks down into hanging (2 to 4 days), taping and mudding (2 to 5 days), and sanding (1 to 3 days), with drying time between coats being the biggest variable. Humid weather can add extra days between mud coats.

Our Process

Assess and plan: walk the space, measure, and figure out sheet layout before any material shows up
Select the right material: standard, fire-rated, moisture-resistant, or soundproof board, based on the room and any code requirements that apply
Hang the sheets: cut, fit, and fasten to studs or joists, staggering seams so joints don’t line up in a straight run
Tape every seam with paper or mesh tape. See our Drywall Finishing & Taping page for more on this step and the coats that follow.
Apply three coats of joint compound, with dry time between each, this is the step that determines whether the wall looks flat or wavy once painted
Sand smooth
Texture match, if the room needs to match adjoining walls or ceilings, see our Texture Matching & Popcorn Ceiling Removal page for more on how this step works
Clean up and do a final walkthrough: leave the space paint-ready, not just technically finished

The bulk of the calendar time on any job isn’t the hanging, it’s waiting for each compound coat to dry before the next one goes on. Rushing that step is the single most common cause of a wall that looks fine at handoff and shows flaws a few months later.

Drywall panel being fixed to ceiling joists with a panel lift

Built for how walls move here

Johnson City takes about 44 inches of rain a year. Board and framing swell through a humid summer and shrink through a dry heated winter, and that cycle is what pops fasteners and opens taped seams. The fix is the right board and enough dry time between coats.

Get a free estimate

Commercial Drywall

Running an office renovation or tenant build-out instead? See our Commercial Drywall page, different code requirements, different scheduling considerations.

See all our services on the Johnson City Drywall homepage.

Does This Job Require a Licensed Contractor?

In Tennessee, drywall work under $3,000 doesn’t require a state contractor license. Jobs between $3,000 and $24,999 require a Home Improvement License in certain counties (mostly larger metro counties. Washington County isn’t one of them, so this tier isn’t a local requirement here). Any job at $25,000 or more requires a full Tennessee Contractor’s License statewide, no exceptions. Most single-room installations fall well under that threshold; a whole-house job or a large addition can approach it, which is worth knowing when you’re comparing contractors and their credentials.

Get Your Installation Started Today

Do not let an unfinished room or a failed inspection hold up your project. Johnson City Drywall provides expert drywall installation that gives your walls and ceilings a smooth, even finish built to last. Contact us today for a free estimate and let our team handle your installation with skill, speed, and precision.

Johnson City Drywall | Drywall Installation in Johnson City, TN FAQs

How much does it cost to install drywall in Johnson City?

A single room hung and finished runs $1,200 to $2,500. Larger jobs price off square footage at $1.50 to $3.00 per square foot. You get an exact quote after we see the space.

How long does a drywall installation project take?

A single room usually takes 2 to 3 days. A full 2,000 sq ft space takes closer to 7 to 10 days, mostly due to drying time between compound coats.

Do you install drywall in garages and basements?

Yes, both require specific board types (fire-rated for garages, moisture-resistant for basements). See our dedicated Garage Drywall and Basement Drywall pages for details.

What type of drywall do you use for bathrooms or basements?

Moisture-resistant (green board) is standard for basements and bathrooms to help prevent mold in humid spaces.

Do you handle both residential and commercial installation?

Yes, see our Commercial Drywall page for tenant build-outs and office renovations.

Can you match existing texture after installation?

Yes, texture matching is part of the finishing process on any tie-in job.

Does my drywall installation need a licensed contractor?

Depends on the job size, see the licensing section above. Most single-room jobs don't require it in Washington County; larger whole-house or addition projects can cross the threshold that does.

What's the difference between a Level 4 and Level 5 finish?

Level 4 is the standard finish under flat paint or light texture. Level 5 adds a full skim coat and is worth the extra cost under glossy or dark paint, or in rooms with strong side-lighting that would otherwise show every seam and fastener.

Towns We Serve Across the Tri-Cities

Get a Free Estimate

Tell us what the damage looks like, or what needs hanging. We come out, look at the wall, and give you a price and a timeline you can hold us to. Repairs start at $150.

Request a Quote Call (423) 820-3689